DIN 8593-5 PDF


Standards. DIN Manufacturing processes joining – Part 5: Joining by forming processes; Classification, subdivision, terms and definitions. Title ( German). DIN references following documents: DIN , , Manufacturing processes joining – Part 5: Joining by forming processes; Classification. Find the most up-to-date version of DIN at Engineering

Author: Mokree Zulkigul
Country: Montserrat
Language: English (Spanish)
Genre: Travel
Published (Last): 19 March 2009
Pages: 113
PDF File Size: 12.9 Mb
ePub File Size: 4.22 Mb
ISBN: 953-8-45063-309-1
Downloads: 22623
Price: Free* [*Free Regsitration Required]
Uploader: Kazrazilkree

VW _2_TOX铆接_图文_百度文库

Table 5 — Abbreviations FLS Measured lap-shear force of the individual specimens [kN] Mean value of the measured lap-shear forces [kN] Fmin Minimum value of the lap-shear force according to drawing [kN] As rough values e. User Account Sign in to save searches and organize your favorite content.

In the case of the conventional riveted joints the maximum load dib of the joint is determined by the strength of the fastener. The result Fmin Ftransverse — 2 sigma is a reference value for the drawing specification. General information — — Part no. The resulting clinched joints are also referred to as joints in the following. EN,Eurocode 3, Design of steel structures, Part Joining by Upset Bulging.

Joining by Upset Bulging

It is the joining of at least two overlapping sheet metal, tube or profile parts achieved by means of cold deformation with punch and die. At least 10 specimens are required for the release tests. The joints were prepared for the three combinations of the Dln steel and EN AW- aluminium alloy sheets with the thickness of 2mm.


Such processes are necessary to di the growing demands on industrial production of multi-material joints and general lightweight production. If undercut is present on both sides: The assessment criteria according to Section 3.

The Structure of the Strength of Riveted Joints Determined in the Lap Joint Tensile Shear Test

This service is more advanced with JavaScript available, learn more at http: J Manuf Process 15 1: From all sheets and rivet specimens arrangements the highest load capacity of the joint was obtained for the 85935 sheet material joints, and the lowest load idn of the joint was obtained for the EN AW sheet material joints.

Beuth, Berlin Google Scholar. With segmented dies, the microsections must be located in the center of the die segments. Here, at least the ratios specified in Table 6 must be achieved: Metallic continuity may occur under certain conditions. Issue 1 First Online: Page 13 VW Undercut f not present on both sides: Mechanical joining ; Tube forming ; Upset bulging.

Synonyms Mechanical joining ; Tube forming ; Upset bulging. Drawing version desired values of the joint: Joining by upset bulging is a mechanical joining process, which is commonly used to create joints with a form and force fit between tubes and other structures, such as sheets, plates, tubes, or profiles.

Previous issues VW There are no generally applicable values for the base thickness tb. Parties to a contract can only obtain this standard via the B2B supplier platform www.

The overall thickness of the joining partners must not 85993-5 5 mm. The joints must be carried out such that window bonding material can be pressed into the recess created by the joining process, see Figure 4. Rectangular joints are to be located perpendicular to the load direction. No part of this document may be transmitted or reproduced without prior permission of a Standards Department of the Volkswagen Group.


The nominal and tolerance values must be determined for each individual case. Page 16 VW Their properties must match to the cases to be tested. These bulges are used to clamp a joining partner e. Page 17 VW If the base is cracked, check for microsection preparation errors. This is a preview of subscription content, log in to check access. The flange height is 35 mm Aalternatively 16 mm B. Joining by forming processes; Classification, subdivision, terms and definitions Clinchen -?

The connection is a positive locking and friction locking joint. For details on the assessment of round clinched joints without cutting element, see PV Especially for round joints, care must be taken that the joint does not fall apart when preparing the microsections.

Living reference work entry First Online: If this is not the case, the joint is NOK. Newer developments, Journal for Technology of Plasticity, Page 15 VW